- Prehľad
- Parameter
- dotaz
- Súvisiace produkty
- Work screen display; display main parameters, such as welding current, welding voltage, welding speed, welding length, etc.
- Human -machine interface setting process parameters, current and speed synchronization curve; built -in multi -sets of mature welded pipe specifications process parameters, each group of process parameters can be adjusted by 12 parameters; the system can permanently save multiple specifications of welded pipe process parameters. The saved parameter can enter the diameter of the welded pipe and the type of material, and directly call the corresponding process parameters.
- With welding short-circuit protection, welding torch position is too low, too high protection.
- With excessive speed fluctuation, with speed and current mismatch protection.
- Air pressure, cooling water pressure warning protection.
- With pay-off, take-up tension is too large, too small protection.
- Each device of the equipment has a separate power control directly on the touch screen, with power status protection monitoring.
- The device operation direction, the right phone, the left to the right. The equipment center is 1m high, the production line length is 35m, the width is 5m, and the height is 3m.
- The total installed capacity of the equipment is less than 70KVA, and the usage is less than 40KVA; the power supply is three-phase five-wire system, 380V/50Hz; the ambient temperature is 5-450C, the ambient relative humidity is MAX95%, and there is no condensation.
- Protective gas: helium, argon; helium flow 160-250L/H, argon flow 50-80L/H; (standard gas cylinder pressure 15MP, gas usage time is about 10 hours). Gas flow PLC touch screen setting, with insufficient gas flow alarm.
- Working gas pressure: >0.4Mpa; water consumption < 1m3/hour.
- Welding shielding gas: Argon or Helium.
- Production line working direction: right hand phone. Facing the device, the left hand pays the line, and the right hand receives the line.
The equipment uses different molds to produce copper, aluminum and stainless steel sheaths for medium-voltage cables, high-speed rail through-ground wires, flexible fire-resistant cables, railway signal cables and other products.The production line uses different molds to produce metal sheaths for railway signal cables, flexible fireproof cables, medium voltage cables, and high-speed copper alloy through-ground cables. After the clean copper strip (or aluminum strip, stainless steel strip) is precisely trimmed, it is formed by longitudinal wrapping with a special mold for welding and forming, and continuous butt longitudinal seam welding is carried out under the protection of inert gas. product.
1 | WeldingOuterDiameter | 8-72mm | |
2 | WeldedMetalStripMaterial | Copper,Aluminum,StainlessSteel | |
3 | WeldedMetalStripThickness | CopperStrip | 0.3 1.2- |
Nehrdzavejúca oceľ | 0.2-0.5 | ||
AluminumStrip | 0.3-2mm | ||
MetalWidth | 20-220mm | ||
4 | WeldingSpeed: 0-20m/min,continuouslyadjustable. | ||
Špecifikácia výrobku | ProductionSpeed m/min | ContinuousWelding Length(km) | |
0.4mmCopperTape | 15.0-20.0 | 2.0 | |
0.5mmCopperTape | 12.0 17.0- | 1.5 | |
0.8mmCopperTape | 5.0 10.0- | 1.0 | |
1.2mmAluminumTape | 15.0-20.0 | 4.0 | |
5 | tractionSpeed | 0-20 / min | |
6 | WeldingMethod | DCargonarc welding,high frequencyarc ignition | |
7 | WeldingCurrent | 5-405A continuously adjustable, 24hours continuousworking current300A | |
8 | EmbossingMethod | Eccentric embossing | |
9 | ProductionProducts | twokindsofring patternandspiral pattern | |
10 | WrinklePitch | 3.5-20mm,online adjustmentwithout stopping | |
11 | WrinkleDepth | 0.5-4mm,online adjustmentwithout stopping |
Nie. | NameOfComponentsThatMakeUpTheProductionLine | Množstvo (súprava) |
1 | ∮2500GantryWalkingPassiveMagneticPowderPay-offRack | 1 |
2 | CableCoreReleaseFixingBracket | 1 |
3 | Pay-offSpeedControlDevice | 1 |
4 | ActiveTapeUnwinderAndTapeSpeedControlDevice | 1 |
5 | TapeMachine | 1 |
6 | WeldingPlatform(withprotectivecover,withweldingfume purificationfunction) | 1 |
7 | WithShapingAndCleaningDevice | 1 |
8 | IncomingBeltPositioningDevice | 1 |
9 | PrecisionFineCutterDevice | 1 |
10 | TapePositioningDevice | 1 |
11 | WasteEdgeWindingDevice | 1 |
12 | PrecisionRollerFormingAndWeldingSizingPlatform (IncludingWheelForming,HornDie,WeldingDie,Sizing Die) | 3 |
13 | Three-DimensionalElectricAdjustmentMechanismOf WeldingTorch | 1 |
14 | StraightHandleWeldingGun | 1 |
15 | TIGWeldingMachine(LincolnTIG-V400) | 1 |
16 | WeldingArcMonitoringSystemAndWeldingSeam AutomatictrackingSystem | 1 |
17 | WeldingGunCoolingCirculationSystem | 1 |
18 | AirSupplyRegulator | 1 |
19 | WeldinglubricationCoolingAndDryingDevice | 1 |
20 | Crawler-TypeMaintractor(Multi-Slot) | 1 |
21 | EccentricHigh-SpeedEmbossingMachine(Max.Speed 4500rpm) | 1 |
22 | EmbossingLubricationCoolingSystem | 1 |
23 | CleaningBlowDryer | 1 |
24 | MeterCounter | 1 |
25 | Take-UpTensionStand | 1 |
26 | ∮2500GantryWalkingTypeAutomaticWindingMachine | 1 |
27 | ElectricalControlSystem | 1 |
28 | AccordingToAnnex3, 22SetsOfProductionMoldsAreProvided | 1 |